应用SPC技术对机械零件加工过程的管理和控制

介绍了SPC(统计过程控制)技术原理，以某传动轴外径φ45 0.50^0.90 mm为控制对象，提出应用SPC技术，对机械零件加工过程进行管理和控制，从而达到过程失控预警、过程不断改进、过程能力不断提高的目的，继而保证产品质量的稳定和不断提高。     

M型四能级原子与三模场相互作用系统的动力学特性

采用全量子理论,研究了M型四能级原子与三模场相互作用系统的动力学特性,通过数值计算,分析了光场失谐量、初始光子数和原子初始状态对原子布居概率和光子统计演化规律的影响.     

静态球对称时空中的标量场辐射

采用多项式函数代替乌龟坐标的方法,给出静态球对称时空中黑洞事件视界和宇宙视界区域内标量场方程的解,并对事件视界附近势垒的性质进行了讨论。发现对带电量不同的时空,标量场辐射的形式亦有所不同;势垒随宇宙学常数的减小而变窄、变高。     

铰孔孔径增大的工艺探析

通过对铰孔孔径增大，误差大产生原因的工艺探讨、分析，提出了有效、切实可行的避免措施，通过灵活应用，提高了产品质量。     

单层开采的圆形定压边界两层油藏压力动态分析

为更好地分析具有越流的多层油藏的压力动态，采用有效井径的概念，在半透壁模型的基础上建立了圆形定压边界、两层越流油藏单层开采时的渗流数学模型。通过拉氏变换得到了拉氏空间中以Bessel函数表示的精确解。数值反演计算结果表明，单层开采的两层油藏与全部打开的两层油藏的压力动态基本相同，都表现为3个阶段：早期是介于两个渗透层之间的均质流动；中间为过渡段，导数曲线出现下凹特征；晚期表现为整个油藏的均质特征。随着边界距离的增加，压力导数值趋近于0．5。半透率越大过渡段出现得越早。导数曲线下凹程度越小；储容比越大导数曲线峰值越小，导数曲线下凹程度越小；随着两层渗透率比值变小。过渡段变短，导数曲线下凹程度变小。图1参9     

Theory of Seepage into an Auger Hole in a Confined Aquifer Overlying a Gravel Substratum

An analytical solution is presented to the problem of steady groundwater flow seeping into a pumped cylindrical hole partially penetrating a homogeneous and anisotropic confined aquifer overlying a gravel substratum. Solutions are obtained for two general cases of the problem: (1) when the level of the pumped hole is below the confining layer; (2) when it is above it. The validity of the proposed theory is tested by comparing analytical predictions obtained for a few flow situations with corresponding results obtained by numerical means. The theory presented here can be utilized to convert the rate of rise of water in a pumped auger hole into directional conductivities of soil, in areas where water is found to be in a confined state overlying a gravel substratum. The study shows that the conductivity values calculated by neglecting the confining pressure of an artesian aquifer with a gravel base [i.e., by applying the existing (Boast and Kirkham in 1971), auger hole seepage theory for a phreatic aquifer with a gravel base to confined situations] may result in serious error; hence, the artesian head of an aquifer must be accounted for while computing the conductivity values. Further, it is observed that the area contributing flow to a pumped auger hole/well with a gravel base is mostly restricted to a short radial distance from the center of the hole, particularly for situations where the gravel substratum is located close to the bottom of the hole. This is in contrast to auger hole flow situations overlying an impervious substratum, where the domain contributing flow is mostly spread out to a considerable distance from the center of the hole.     

The validity of psychophysiological detection of information with the Guilty Knowledge Test: A meta-analytic review.

The authors performed a meta-analysis based on 169 conditions, gathered from 80 laboratory studies, to estimate the validity of the Guilty Knowledge Test (GKT) with the electrodermal measure. The over-all average effect size was 1.55, but there were considerable variations among studies. In particular, mock-crime studies produced the highest average effect size (2.09). Three additional moderators, were identified: Motivational instructions, deceptive ("no") verbal responses, and the use of at least 5 questions were associated with enhanced validity. Finally, a set of 10 studies that best approximated applications of the GKT under optimal conditions produced an average effect size of 3.12. The authors discuss factors that might limit the generalizability of these results and recommend further research of the GKT in realistic setups. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Stabilization techniques for spectral methods

We introduce a stabilized treatment of spectral methods. The condition number of the spectral systems is highly improved. Elliptic and biharmonic problems are considered. Suitable interpolants in the case of inhomogeneous Dirichlet boundary conditions are presented. For a direct solver the improvements with respect to rounding error propagation are numerically demonstrated.     

模糊环境的表示及机器人轨迹规划

本文利用模糊集理论，提出一种非确定环境的描述方法，并且针对机器人在该类环境中的避障轨迹规划，建立了相应的决策函数和规划策略，最后，给出在ＰＣ－３８６计算机上的仿真试验结果。     

井巷掘进控制斜形炮孔钻孔精度的试验研究

井巷掘进爆破工程中，工作面按设计要求，布置各种斜形炮孔，利用量角器和垂直尺控制钎杆与工作面夹角，使炮孔钻孔精度与设计炮孔角度基本上符合，在生产中取得了良好的爆破效果．